Carburant Diesel
Capacité (M3) 1.18
Ave Capacity 750 kg
Consommation (l/h) 6
Dimension externes
Longueur (mm) 3110
Largeur (mm) 1800
Hauteur (mm) 3300
Ouverture Porte 770×2000
Dimension internes
Longueur (mm) 2100
Largeur (mm) 700
Hauteur (mm) 800
Opération
Minimum température d’opération 950
Maximum température d’opération 1320
Température de suivi oui
Thermostat oui
Ventilateur oui
Chambre de combustion secondaire secs
garantie minimum 12 mois

Carburant Diesel
Capacité (M3) 1.92
Ave Capacity 1200kg
Consommation (litre/heure 12
Dimension externes
Longueur (mm) 3110
Largeur (mm) 2150
Hauteur (mm) 3200
Ouverture Porte 1000×2000
Dimension internes
Longueur (mm) 2200
Largeur (mm) 1050
Hauteur (mm) 800
Opération
Minimum température d’opération 950
Maximum température d’opération 1320
Température de suivi oui
Thermostat oui
Ventilateur oui
Chambre de combustion secondaire 2 secs
garantie minimum 12 mois

				COMPLIANCE (YES, NO or COMMENT)
Item Description			Medical Waste Incinerator, 50 to 60 Kg/hr
Item Quantity			5 No.
Support			Health Sector Support Project
Point of Installation (Hospitals)			Moi Voi, Makindu, Maragua, Eldama Ravine and Isiolo District Hospitals
1.     General Description Supply, delivery, installation and commissioning of a medical waste incinerator suitable for disposal of Medical, General and Pathological waste in a safe and clean environment. The unit shall consist of two chambers and operate on the principal of controlled air and temperature. The unit shall consist a particulate remover (scrubbers) as stipulated in waste management regulations, 2006 (Legal notice NO. 121 of 29th September, 2006). The Unit shall be fully automatic and controlled by an automatic electronic controlled system except loading system which shall be manual.   The unit shall be capable of incinerating between 50 to 60 kg of solid medical waste per hour. It shall be constructed from mild or aluminized steel lined with refractory material.
2.   Composition 2.1     Main unit 2.2   Accessories
3.   Performance specifications
3.1	Main unit
3.1.1	Application	For incineration, general and pathological
3.1.2	Capacity	50 – 60 kg/h burn rate
3.1.3	Type	Two combustion chambers type; primary and Secondary, controlled/forced combustion air type with a flue gas emission scrubbing unit
3.1.4	Operating time	Minimum 8 hours daily
3.1.5	Operating temperature	From 850 0C to 1200 0C, Automatic controlled
3.1.6	Residual Ash	5 to 10%
3.2       Primary Chamber
3.2.1	Construction	Constructed from heavy duty mild or aluminized steel Or equal and approved equivalent
3.2.2	Insulation material	Refractory material lining similar or equal to calcium Silicate and hot face combination of heavy duty brickwork
3.2.3	Internal Construction	Fixed hearth type complete with gratings, concave bottom and charging door, lined with refractory material
3.2.4	Charging Door	Suitable for manual loading of wastes and with smooth Dear seal equivalent of Ceramic seals with hinges.
3.2.5	Door Lock	Automatic, Electric type
3.2.6	Ash removal door	Provided, for removing resultant bottom ash leftovers                             from the Primary chamber
3.2.7	Gratings	Provided
3.2.8	Loading	Manual loading of waste
3.2.9	Primary Burner	Fully automatic, with fuel, temperature and speed controls with ignition system, flame detector, Air fan complete with safety features, flame failure, Diesel fired fuel injector type and Flange mounted
3.2.10	Blower	Provided. For supplying excess combustion air through the distribution system with speed control system
3.2.11	Temperature	Minimum exit 850 0C
3.2.12	Observation port	To be provided with protective glass type
3.3       Secondary chamber
3.3.1	Construction	Constructed from heavy duty mild or aluminized steel or equal and approved equivalent
3.3.2	Insulation	Refractory material lining
3.3.3	Combustion Temperatures	Above 850 0C, controlled electronically
3.3.4	Gas residue or retention Time	> 2 second at minimum 850 0C
3.3.5	Secondary Burner	Provided, Diesel fired, fully automatic, with fuel, temperature and speed controls, With ignition system,                                                                   Flame detector, Air fan, Complete with safety features, flame failure Diesel fired fuel injector type.                                                                   Flange mounted
3.3.6	Ejector	Provided, Venturi type, for cooling the flue gases
3.3.7	Combustion Air Fan	Provided for supplying combustion and creating a negative drift and turbulences
3.3.8	Temperature	Maximum 1600 0C
3.4       Chimney
3.4.1	Construction	Constructed from heavy duty mild or aluminized steel   or equal and approved equivalent                                                                   Refractory material lining
3.4.2	Length	10 m above ground
3.4.3	Bore	about 350mm diameter
3.4.5	Discharge temperatures	About 850 0C
3.4.6	Emissions	To comply with standards in section 9 of third schedule of the waste management regulations, 2006.
3.5         Electrical System
3.3.5	Control unit	Fully automatic with microprocessor based control                                                                       unit (PLC) automating all operations of the                                                                       incinerator. Capable of monitoring all incinerator parameters With large LCD or similar for display of all progress Parameters i.e. temperature of primary and secondary chambers, turbulence and time With status lamp With user of defined and differed programmed operating cycles for different type of loads/conditions With safety interlocks, display of errors and visible and audio alarms. System for continuous emission monitoring
3.5.2	Isolator switch	Supply and install isolator switch 240V, 100A for the                                                                     incinerator unit, including all necessary cables 10m
3.5.3	Distribution Board	Supply and install distribution board. 100 A, complete with MCBs suitable for the rating of the incinerator unit and associated equipment. Wiring     to be done according IEE regulations.
3.5.4	Wiring	Make provisions for wiring the isolator switch, Distribution Board control unit to Incinerator and all associated equipment inside to incinerator room.                                                                         Working length 20m. Wiring to be done using PVC Sheath cable on steel conduits and trucking and in accordance with IEE regulations
3.6	Fuel System	Supply and install storage fuel tank inside the incinerator room at an elevated position (about 1.5 m above the floor)
3.6.1	Fuel Tank	Tank capacity, 400 liters, constructed from preferable suitable metallic material or high temperature resistance material
	Fuel type	Diesel
3.6.2	Fuel Lines	Supply and install fuel lines, complete with fuel filters, pump, sight glass, fuel level and all other safety devices and connect from fuel tank to incinerator. Working length , 20m Fuel pipe material; Special copper pipes or similar                                                                         and approved materials
4               Physical characteristics
4.1	Main unit	Floor mounted, stand alone, fixed hearth type
	Dimensions	About 1.2 x 2.2m (WxD)
5   Operating environment
5.1	Power Requirements	240V,A/C 50Hz, single phase, with PE
	Ambient temperature	10 0C to 40 0C
	Relatively humidity	40% to 90%
6. Accessories
	Rack, 2 m long	1 piece
6.1	Waste cart, stainless steel	1 piece
7	Spare parts
7.1	Burner	1 set
7.2	Fuel Filters	6 sets
7.3	All other spare parts                     required for replacement during and after 12 months of operations.	2 pieces of each
8               Quality Standards
8.2	Manufacturing standards	NEMA Kenya Act, 1999 Legal Notice No.121 of 29th September 1999 on waste Management Regulations EU waste incinerator Directive- EC 76/2000 BS 3316 WHO Emission Standards World Bank Emission Standards or any other internationally recognized standards
	Conformity to standards	CE marked or any other internationally recognized documents
9         Local back up service
9.1	Available	Should be available locally
9.2	Capacity to service equipment	Manufacturer/Agent shall have adequate facilities, spare parts, qualified and skilled technical staff to offer comprehensive maintenance   service and spare parts sales for the lifespan of the incinerator
10         Delivery point
10.1	KEMSA	For inspection and verification
10.2	Moi Voi, Makindu Maragua, Eldama Ravine and Isiolo Hospitals	For installation, testing, NEMA Certification and commissioning
11	Pre installation works	Provide for foundation plinth, necessary plumbing works, Fuel piping works, Elevated Diesel oil storage tank, electrical works including cabling, trunking and switch gears required to install the incinerator and all its accessories to required IEE standards
12	Installation and testing	Complete installation and set up of the incinerator at designated as per manufacturer’s instructions Provide fuel and test run the incinerator for 3 hours daily for 7 days
13	Training
13.1	User training	On site user training on operation and daily up keep
13.2	Maintenance training	On-site maintenance training on Preventive Maintenance, repair and trouble shooting
14	Technical Documentations
14.1	User manuals	2 sets
14.2	Service manuals	2 sets
14.3	Drawings	2 sets
15         Commissioning
15.1	Testing and Commissioning of the machine to the satisfaction of the user
16	Warranty
16.1	Equipment	Minimum of one year after commissioning on all parts.
16.2	Equipment system	Nil
17.   Maintenance contract
17.2	Comprehensive preventive & repair           service	Provided a 12 months comprehensive preventive and repair service contract inclusive of spare parts and material from date of commissioning

				COMPLIANCE (YES, NO or COMMENT)
Item Description			Medical Waste Incinerator, 100 to 120 Kg/hr
Item Quantity			3 No.
Support			East African Networking Project
Point of Installation (Hospitals)			Wajir, Kitale, and Busia District Hospitals
General Description Supply, delivery, installation and commissioning of a medical waste incinerator suitable for disposal of Medical, General and Pathological waste in a safe and clean environment. The unit shall consist of two chambers and operate on the principal of controlled air and temperature. The unit shall consist a particulate remover (scrubbers) as stipulated in waste management regulations, 2006 (Legal notice NO. 121 of 29th September, 2006). The Unit shall be fully automatic and controlled by an automatic electronic controlled system except loading system which shall be manual.   The unit shall be capable of incinerating between 100 to 120 kg of solid medical waste per hour. It shall be constructed from mild or aluminized steel lined with refractory material.
Composition 2.1     Main unit 2.2   Accessories
Performance specifications
3.1	Main unit
3.1.1	Application	For incineration, general and pathological
3.1.2	Capacity	100 – 120 kg/h burn rate
3.1.3	Type	Two combustion chambers type; primary and Secondary, controlled/forced combustion air type with a flue gas emission scrubbing unit
3.1.4	Operating time	Minimum 8 hours daily
3.1.5	Operating temperature	From 850 0C to 1200 0C, Automatic controlled
3.1.6	Residual Ash	5 to 10%
3.2     Primary Chamber
3.2.1	Construction	Constructed from heavy duty mild or aluminized steel Or equal and approved equivalent
3.2.2	Insulation material	Refractory material lining similar or equal to calcium Silicate and hot face combination of heavy duty brickwork
3.2.3	Internal Construction	Fixed hearth type complete with gratings, concave bottom and charging door, lined with refractory material
3.2.4	Charging Door	Suitable for manual loading of wastes and with smooth Dear seal equivalent of Ceramic seals with hinges.
3.2.5	Door Lock	Automatic, Electric type
3.2.6	Ash removal door	Provided, for removing resultant bottom ash leftovers                             from the Primary chamber
3.2.7	Gratings	Provided
3.2.8	Loading	Manual loading of waste
3.2.9	Primary Burner	Fully automatic, with fuel, temperature and speed   controls with ignition system   flame detector                                                           Air fan Complete with safety features, flame failure                                                                     Diesel fired fuel injector type Flange mounted
3.2.10	Blower	Provided. 3 phase for supplying excess combustion air through the distribution system with speed control system
3.2.11	Temperature	Minimum exit 850 0C
3.2.12	Observation port	To be provided with protective glass type
3.3     Secondary chamber
3.3.1	Construction	Constructed from heavy duty mild or aluminized steel or equal and approved equivalent
3.3.2	Insulation	Refractory material lining
3.3.3	Combustion Temperatures	Above 850 0C, controlled electronically
3.3.4	Gas residue or retention time	> 2 second at minimum 850 0C
3.3.5	Secondary Burner	Provided, Diesel fired, Fully automatic, with fuel, temperature and speed controls With ignition system Flame detector Air fan Complete with safety features, flame failure Diesel fired fuel injector type Flange mounted
3.3.6	Ejector	Provided, Venturi type, for cooling the flue gases
3.3.7	Combustion Air Fan	Provided for supplying combustion and creating a negative drift and turbulences with variable speed control
3.3.8	Temperature	Maximum 1600 0C
3.4         Chimney
3.4.1	Construction	Constructed from heavy duty mild or aluminized steel   or equal and approved equivalent Refractory material lining
3.4.2	Length	10 m above ground
3.4.3	Bore	about 350mm diameter
3.4.4	Discharge temperatures	About 850 0C
3.4.5	Emissions	To comply with standards in section 9 of third schedule of the waste management regulations, 2006.
3.5       Electrical System
3.5.1	Control unit	Fully automatic with microprocessor based control unit (PLC) automating all operations of the incinerator Capable of monitoring all incinerator parameters With large LCD or similar for display of all progress Parameters i.e. temperature of primary and second chambers , turbulence and time With status lamp With user of defined and differed programmed operating cycles for different type of loads/conditions With safety interlocks, display of errors and visible and audio alarms. System for continuous emission monitoring
3.5.2	Isolator switch	Supply and install isolator switch 100A, 3 phase, 415V, 50Hz, for the incinerator unit , including all necessary cables 10m
3.5.3	Distribution Board	Supply and install distribution board 100 A, 3 phase 415V, 50Hz, complete with MCBs suitable for the rating of the incinerator unit and associated equipment. Wiring   to be done according IEE regulations.
3.5.4	Wiring	Make provisions for wiring the isolator switch, Distribution Board control unit to Incinerator and all associated equipment inside to incinerator room. Working length 20m. Wiring to be done using PVC Sheath cable on steel conduits and trucking and in accordance with IEE regulations
3.6     Fuel System
3.6.1	Fuel Tank	Supply and install storage fuel tank inside the incinerator room at an elevated position (about 1.5 m above the floor)
		Tank capacity, 500 liters, constructed from preferable suitable metallic material or high temperature resistance material
	Fuel type	Diesel
3.6.2	Fuel Lines	Supply and install fuel lines, complete with fuel filters, pump, sight glass, fuel level and all other safety devices and connect from fuel tank to incinerator. Working length , 20m
	Fuel pipe material	Special copper pipes or similar and approved materials
Physical characteristics
4.1	Main unit	Floor mounted, stand alone, fixed hearth type
	Dimensions	About 2.5 x 2.8m (WxD)
Operating environment
5.1	Power Requirements	415V, A/C 50Hz, Three phase, with PE
	Ambient temperature	10 0C to 40 0C
	Relatively humidity	40% to 90%
6               Accessories
6.1	Rack, 2 m long	1 piece
	Waste cart, stainless steel	1 piece
Spare parts
7.1	Burner	1 set
7.2	Fuel Filters	6 sets
7.3	All other spare parts                 required for replacement during and after 12 months of operations.	2 pieces of each
8               Quality Standards
8.2	Manufacturing standards	Environmental Management and Coordination Act, 1999 Legal Notice No.121 of 29th September 1999 on                                                                           waste Management Regulations EU waste incinerator Directive- EC 76/2000 BS 3316 WHO Emission Standards World Bank Emission Standards or any other internationally recognized standards
	Conformity to standards	CE marked or any other internationally recognized documents
9           Local back up service
9.1	Available	Should be available locally
9.2	Capacity to service equipment	Manufacturer/Agent shall have adequate facilities, spare parts, qualified and skilled technical staff to offer comprehensive maintenance   service and spare parts sales for the lifespan of the incinerator
10         Delivery point
10.1	KEMSA	For inspection and verification
10.2	Moi Voi, Makindu Maragua, Eldama Ravine and Isiolo Hospitals	For installation, testing, NEMA Certification and commissioning
11	Pre installation works	Provide for foundation plinth, necessary plumbing works, Fuel piping works, Elevated Diesel oil storage tank, electrical works including cabling, trunking and switch gears required to install the incinerator and all its accessories to required IEE standards
12	Installation and testing	Complete installation and setup of the incinerator at designated as per manufacturer’s instructions Provide fuel and test run the incinerator for 3 hours daily for 7 days
13	Training
13.1	User training	On site user training on operation and daily up keep
13.2	Maintenance training	On-site maintenance training on Preventive Maintenance, repair and trouble shooting
14	Technical Documentations
14.1	User manuals	2 sets
14.2	Service manuals	2 sets
14.3	Drawings	2 sets
15         Commissioning
15.1	Testing and Commissioning of the machine to the satisfaction of the user
16	Warranty
16.1	Equipment	Minimum of one year after commissioning on all parts.
16.2	Equipment system	Nil
Maintenance contract
17.2	Comprehensive preventive & repair           service	Provided a 12 months comprehensive preventive and repair service contract inclusive of spare parts and material from date of commissioning

incenratory

Gilgit-Baltistan Environmental Protection Agency intends to mange hospital waste through piloting of three major districts headquarter hospitals (Hunza/Nagar, Skardu, Chillas and Gilgit and city hospital Gilgit) through integrated Solid/Biomedical Waste management.

 

For this purpose GBEPA has planned to procure solid/biomedical waste incinerators with other necessary equipment through open competitive Single stage (two envelop technical and financial) bidding as per PPRA Rules on the criteria as under:

 

 

		All bids will be evaluated under Single stage two envelope bidding
		procedures,  The bidders will be evaluated on technical and financial grounds.
		Price will be taken into account after technical evaluation.
1.		CRITERIA FOR TECHNICAL EVALUTAION

For technical evaluation the bidder/firm has to be evaluated under the following criteria;

1. Relevant past experience of establishment of integrated solid/bio-medical waste management system
2. Capabilities with respect to personnel, equipment, technical expertise, and supply networ

• Appropriate capacity building opportunities

 

1. Repair and maintenance of equipment and machinery to be supplied

 

1. Capacity building of staff to operate machinery/equipment

 

1. Manufacturing/ dealerships within Pakistan

 

• Financial strength of bidder/firm
• Technical, financial capabilities with adequate managerial capabilities of the fir

 

1. Legal status of firm, blacklisting /any litigation in any court of law within Pa
2. The bidders have to submit bidding documents in a sealed package with Single Stage two envelop bidding (technical and financial).
3. Technical and financial Evaluation committee reserves the right to accept or reject any or all bidders/firms without assigning any reason there

• The evaluation of Bids will be based on technical evaluation by the Evaluation Committee which is based on 500 points (100 points for each technical capacities)

TECHNICAL EVALUATION POINT 500

S#	Technical Expertise	Maximum Points	Points obtained
01	Past     experience     and   proof   of     Installation       &operation/manufacturing/distribution of integrated solid/bio-medical waste Incinerators in working conditions in any public sector hospitals in Pakistan	100
02	Personnel, equipment, technical expertise,manufacturing /dealership of machinery within Pakistan.	100
03	Capacity building opportunities for running andmaintenance of machinery/equipment (Trainings of hospital staff)	100
04	Repair Maintenance of machinery and equipment aftersale and service facility	100
05	Financial strength of firm/bidder	100

 

 

After acceptance of technical and financial bids the bidder/firm has to supply the equipment/machinery as per specifications provided by GBEPA, equipment will be supplied on respective districts as per agreement with 30 days of the issuance of supply order.

 

2. Equipment List

Following is the list of Machinery and Equipment

1. Incinerators 05 Nos
2. Primary Waste Collection Bins Sets (Red, Yellow, Green) Bulk

• Secondary Containers (Red, Yellow, Green) Bulk

1. Tertiary Containers Eight (optional)
2. Personal Protective Equipment (PPEs) Bulk
   1. Gloves
   2. Masks
   3. Shoes
   4. Coverall (protective Clothing for waste handling workers)

 

VI.	Trolleys for Waste Transfer	Thirty
VII.	Signage’s	Bulk
VIII.	Standard shovels or tools for waste loading/unloading	Bulk
IX.	Tagging Bags for waste handling at primary level	Bulk
3.	Specifications

Following are the detailed specifications and terms and conditions for each equipment / machines;

• Incinerator:

Chamber                                           Double

Burning Rate                                  10 kg per hour (for two incinerators)

Burning Rate                                  20 kg per hour (for three incinerators)

Loading Method                          Manual

No of Burners                                Single for 10 kg/hour and Double for 20 kg per hour Fuel       Diesel and Natural Gas

Warm Up Time                              Not more than 20 minutes

Temperature controller          Digital

Power Supply                                 Single Phase 220V

Chimney Height                            20 feet from ground level

Wet and Dry Scrubbers           Optional

 

Terms and Conditions for Incinerator Supply:

 

• General

 

1. Bidders shall provide 5% of the total cost as bid securit
2. Bidders are   required   to    provide    warranty    of    the    equipment    as    per recommendations of the Original Equipment Manufacturer (OEM).

 

 

• Bidders should provide printed brochures of the equipment elaborating details of specifications, brand name, model and capacity etc.

 

1. Bidders / firms should also provide proof of past experience of establishment of hospital waste management system and piloting with training and capacity building of procuring agency /authorities with proof of dealership within Pakistan and availability of spare parts in fut

 

• Specific
  1. Installation and Operation:

 

1. Transportation and installation at selected points in the project are
2. Construction of civil infrastructure as per requirement of the Incinerators, transfer and transport system in consultation and consent of GB-EP
3. Fixing of incinerators at designated sites with standardized procedures as per agreed by GBEP
4. Technical testing of the installed incinerators for minimum of two week

1. Training:
   1. Develop standard operating procedures in consultation with GBEP
   2. Develop training module for plant operator’s in-lines with agreed SOPS.
   3. Impart training to Hospital Plant operators (incinerator operators).

• Maintenance:
  1. Develop manual for minor maintenance for troublesh
  2. Provide basic accessories required to maintain operation as spare parts of the equipmen
  3. Provide one year free of cost maintenance of the system according to the warranty provided by OEM

1. Work Plan/Documentation
   1. Provide detailed work plan including BOQ’s (bill of quantities).

 

1. Submit detailed design of the each project with spe

 

1. Submission of project completion report

 

1. Financial Plan
   1. 50% of the approved tender cost will be given on transportation and installation off machinery/equipment at project
   2. 30% of the remaining cost will be paid on completion of II & III.
   3. 20% will be paid after satisfactory results of the project or mutual agreement of both partie

 

• Specifications for Primary and Secondary Waste Collection Bins:

Color                           Red, Yellow and Green

Material                      Plastic or Composite

Strength                      Strong enough to handle waste

Made                           By any reputed company

 

• Specifications for Waste Transfer Trolleys

Color                           Any

Material                      Metallic

Strength                      Strong enough to carry waste of 10 kg to a distance of 100 meters

Made                           By any reputed company

• Specifications for Signage’s

Signage’s and billboards of standard designs and material for installation at various locations of Hospitals carrying waste handling and awareness messages.

 

• Specifications for PPE’s

Gloves, Masks and Safety shoes made by any reputed company complying international safety standards.

 

• Specifications for Standard Shovels or Tools for Waste Loading / Unloading

Metallic or any other standard material made any reputed company

 

• Specifications for Tagging Bags

Plastic bags with printed identification of the purpose of infectious waste handling at primary level